A practical brazing course finishing with an exam and a brazer certificate according to EN ISO 13585 – ideal for refrigeration, HVAC and copper pipework technicians. The course can be taught and examined in English. We set the date as soon as the group is full – leave us your contact details and we will get in touch.

The primary aim of soldering is to create a strong and functional bond between two or more components. This bond is achieved by molten solder which flows into the narrow joint gap (in capillary soldering) or is applied on the surface (in overlay soldering) and forms a metallurgical bond upon cooling. Soldering is used to join individual parts (joining soldering) or to create a surface layer with specific properties (overlay soldering).
The basic principles of soldering rely on several physical phenomena that enable the formation of a quality joint:
Wettability: The ability of molten solder (and flux) to adhere to a clean surface of the material being joined at a specific temperature. The quantitative criterion is the wetting angle. Excellent to acceptable wettability (angle 0-90°) is desirable for good soldering.
Spreadability: The ability of molten solder to spread over a horizontal surface of the base material at a given temperature. It is assessed by the area size over which a defined amount of solder spreads.
Capillarity: The ability of molten solder to fill a narrow joint gap by capillary forces. The strength of capillary action depends on the solder type, base material, and the width and shape of the gap.
Diffusion: During soldering, atoms of the solder and base material move at the interface, contributing to the metallurgical bond.
Dissolution: Alongside diffusion, dissolution of the base material in the molten solder may occur in the transition zone.
For successful soldering, it is important to achieve good wettability, spreadability, and capillarity (in capillary soldering) of the solder on the base material, ensuring the joint is filled and a strong bond is formed through diffusion and possible dissolution.
Compared to welding, soldering has several advantages and limitations:
Flux is a chemical agent that aids soldering by removing surface oxides from the soldered area and protecting it from further oxidation. The type of flux is chosen based on the base material and the soldering temperature of the solder used.

Fluxes are classified according to the soldering method into:
Fluxes for soft soldering
Fluxes for hard soldering
According to their effect, fluxes are divided into:
Active fluxes
Non-active fluxes
Flux labelling follows standard STN 05 5705, where flux codes begin with FB (Flux Brazing) and include numerical codes indicating the flux's intended use (for heavy or light metals), soldering type (hard or soft), and activation temperature. An important property of flux is its activation temperature, which must be at least 50 °C lower than the solidus temperature of the solder. The flux must also wet the base material and solder well, and its residues should be easily removable after soldering.
Solder is the filler material used in soldering, which has a lower melting point than the base material. Hard solders are used for hard soldering and are categorised into different groups based on their chemical composition:

Aluminium-based hard solders (AL): Based on Al-Si, used for soldering aluminium.
Magnesium-based hard solders: Based on Mg-Al-Zn-Cd/Be, designed for soldering magnesium alloys.
Copper-based hard solders (CP, CU): Suitable for soldering ferrous and non-ferrous metals with melting points above 1000 °C. These include Cu, Cu-P and Cu-Zn solders. Cu-P and Ag-Cu-P solders do not require flux when soldering copper and silver.
Hard silver solders (AG): Categorised by chemical composition into Ag-Cu, Ag-Cu-P, Ag-Cu-Zn, Ag-Cu-Sn, Ag-Cu-Zn-Cd, Ag-Cu-Zn-Sn/In, Ag-Cu-Zn-Ni-Mn and Ag-Cu-Ti. Used for soldering various metals including ferrous and non-ferrous metals, stainless steels, and sintered carbides.
Various types of equipment are used in brazing to heat the joint and apply the filler metal:
Flame brazing is still the most widely used method of both soft soldering and brazing. Its main advantage over other methods is the low investment cost of equipment and accessories. The equipment is similar to that used for gas welding and consists of:
Unlike resistance brazing, the brazed part is not part of a closed electrical circuit. It is placed inside an inductor, which acts as the short-circuited secondary winding of a transformer. The inductor coil induces eddy currents in the workpiece, and these currents generate heat.
Furnace brazing allows larger or more complex parts to be heated evenly. Depending on the furnace atmosphere, we distinguish brazing in normal atmosphere with flux, in a protective atmosphere (e.g. nitrogen, argon), in a reducing atmosphere (e.g. hydrocarbon gases) and in vacuum.
Uses the electrical resistance of the material to generate heat directly at the joint.
Brazing is widely used across industry wherever metal parts must be joined reliably yet gently. Thanks to lower working temperatures than welding and the ability to join dissimilar materials, it has become an essential technology where precision, appearance and minimal heat input into the base material matter. Typical applications include:
Joining precision parts, tools and thin-walled components where welding could cause distortion or change the material properties.
Strong, leak-tight pipe joints that must withstand pressure and prevent refrigerant leaks.
Production of heat exchangers, sensors and other components that must be light, strong and reliable even under high loads.
Joining conductors, contacts and connectors where good conductivity and mechanical strength are required.
Precise, discreet joining of precious metals without damaging their shape or surface finish – ideal for making and repairing jewellery.
If you are interested in brazing and want to expand your knowledge or obtain certification according to EN ISO 13585, sign up for our course at T&W Academy – taught and examined in English or Slovak.
I am interested in the course →Course enquiry
Leave us your contact details and we will get back to you with the dates, price and course content.
Prefer to call or write?
We have received your enquiry and will get back to you as soon as possible, usually within one working day.